2017 Mazda3 · US · Wipers and glass

Replace original Mazda3 hatchback rear wiper rubber

Replace the rubber in the original 5-Door rear wiper holder, retain its metal stiffeners and refit the matched cover and optional stopper before a wet-glass comparison.

1 Confirm your vehicle

For 2017 Mazda3 · US, SKYACTIV-G 2.0 / 2.5 gasoline. Required equipment: 5-door hatchback

Your vehicleEquipment or remote type

I checked the US model year, gasoline engine and component against the manual.

Select and confirm your vehicle before starting.

Help identify your model and equipment

What is excluded?

Other model years or markets, Axela / diesel and aftermarket equipment with a different procedure.
4-Door sedans have no covered rear-wiper procedure. Aftermarket holders, arm adjustment, a seized pivot, glass damage, an unknown cover or stopper and an unconfirmed replacement rubber are outside this plan.

2 Prepare

You can save preparation while your vehicle or equipment is still unconfirmed.

Park away from traffic, set the parking brake and keep the ignition off unless a final parked functional observation explicitly requires the normal controls.Is this a 2017 US Mazda3 5-Door with the original rear holder and cover shown on printed pages 6–33/34, matching replacement rubber, its stopper type identified and a way to support the arm without striking the glass?The matching manual illustrations on printed pages 6–33/34A clear workspace where the raised arm can remain supportedReplacement rear blade rubber confirmed for the actual original holder; the cited procedure gives no universal length or part number

YOUR OBSERVATIONS

Keep the before and after.

Only on this device

Record the hatchback equipment match, stopper type, replacement rubber, retained stiffeners, final attachment and the actual wet-glass observation. Keep any incomplete step visible.

Observation date

5-Door original rear holder / cover and stopper typeActual replacement rubber matched to holderOriginal stiffeners retained without bendingBlade, cover and applicable stopper retentionSafe parked wet-glass resultUnresolved defect and next action

Before the checkAfter the check

After full refitting, compare the same rear viewing area on wet glass while parked. No wet observation means incomplete work; persistent noise, streaks or loose movement needs inspection.

Recheck resultNotes for the next step

3 Follow the steps

Confirm compatibility and choose the readiness branch before recording steps.

Check that the rear rubber is worn or cracked rather than only contaminated; use the linked cleaning plan for contamination. Confirm the 5-Door original attachment. Switch the wiper controls and ignition off before handling it. Do not drag the wiper through its sweep by hand.Manual reference · PDF 445; printed 6–32
Compare the actual cover with the illustration on printed page 6–33, then remove that cover. On the stopper-equipped type, remove the stopper before raising the arm; on the type without a stopper, raise the arm directly. Keep the arm supported throughout and stop if the parts differ or do not release as illustrated.Manual reference · PDF 446; printed 6–33
With the arm supported, rotate the blade to the right in the direction shown in the manual illustration until its attachment unlocks, then remove the blade. This rotates the blade on its attachment; it does not mean forcing the arm through its sweep. Never let the uncovered arm fall onto the rear window.Manual reference · PDF 446; printed 6–33
Pull the old rubber down and slide it out of the blade holder. Keep the holder and its original metal stiffeners together. Remove the stiffeners from the old rubber and install them in the confirmed replacement rubber; do not bend or discard them.Manual reference · PDF 446; printed 6–33
Carefully insert the replacement rubber into the holder as shown on printed page 6–34. Reinstall the blade assembly in the reverse order of removal. Supporting the arm, return it gently to the glass; restore the stopper on the type that uses it and refit the cover. Confirm each removed part is securely back in its original place before using the controls.Manual reference · PDF 447; printed 6–34
For the result record, with the assembly complete and everyone clear, wet the rear glass and observe the wiper using the normal controls while parked. Record wiping coverage, noise and any looseness; do not run the test on dry glass. If the wet observation is pending, save incomplete work. Stop operating a loose blade or one that moves abnormally.Manual reference · PDF 447; printed 6–34

4 Check the result

Matching rubber installed, original stiffeners reused, holder / cover / applicable stopper secured and satisfactory wet wiping observed
After full refitting, compare the same rear viewing area on wet glass while parked. No wet observation means incomplete work; persistent noise, streaks or loose movement needs inspection.
Preserve any unresolved defect and its next action; a completed web record does not certify a repair.

Select what you actually observed. If you have only prepared the plan, record that instead.

Stop and get help if

A mismatched attachment, stuck cover or stopper, bent stiffeners, damaged glass, insecure refitting or abnormal movement during the wet-glass check
Stop for mismatched or stuck fittings, bent stiffeners, damaged glass or insecure refitting. Keep the wiper off if it is loose or moves abnormally and ask Mazda or a suitable repairer to inspect the attachment.
Stop if the actual part, attachment or surface differs from the matched manual.

Source & applicability

2017 Mazda3 — Rear Wiper Replacement Scope and Precautions
PDF 445; printed 6–32 · Source checked 2026-10-25
2017 Mazda3 — Rear Wiper Cover, Stopper, Holder and Stiffeners
PDF 446; printed 6–33 · Source checked 2026-10-25
2017 Mazda3 — Rear Wiper Rubber Installation
PDF 447; printed 6–34 · Source checked 2026-10-25

Original, AI-assisted plan based on owner-manual facts. No physical repair test or manufacturer endorsement is claimed. Content version 2.0.0.

All observation paths

Is this a 2017 US Mazda3 5-Door with the original rear holder and cover shown on printed pages 6–33/34, matching replacement rubber, its stopper type identified and a way to support the arm without striking the glass?

Yes — equipment, materials and safe conditions confirmed: Follow the matched-equipment plan and record only what you actually do and observe.
Not yet / uncertain: Preparation saved. Confirm the equipment, material and safe conditions before proceeding.
A mismatched attachment, stuck cover or stopper, bent stiffeners, damaged glass, insecure refitting or abnormal movement during the wet-glass check: Stop for mismatched or stuck fittings, bent stiffeners, damaged glass or insecure refitting. Keep the wiper off if it is loose or moves abnormally and ask Mazda or a suitable repairer to inspect the attachment.

After the complete assembly is refitted, what did the safe parked wet-glass check show?

Matching rubber installed, original stiffeners reused, holder / cover / applicable stopper secured and satisfactory wet wiping observed: The rear-rubber replacement and actual wet-glass result are recorded. Continued noise, streaks or insecure retention still needs inspection.
A mismatched attachment, stuck cover or stopper, bent stiffeners, damaged glass, insecure refitting or abnormal movement during the wet-glass check: Stop for mismatched or stuck fittings, bent stiffeners, damaged glass or insecure refitting. Keep the wiper off if it is loose or moves abnormally and ask Mazda or a suitable repairer to inspect the attachment.
Work or the repeat observation is still incomplete: Preparation or incomplete work recorded. A satisfactory repeat observation is still pending.

All observation paths

Is this a 2017 US Mazda3 5-Door with the original rear holder and cover shown on printed pages 6–33/34, matching replacement rubber, its stopper type identified and a way to support the arm without striking the glass?

Yes — equipment, materials and safe conditions confirmed: Follow the matched-equipment plan and record only what you actually do and observe.
Not yet / uncertain: Preparation saved. Confirm the equipment, material and safe conditions before proceeding.
A mismatched attachment, stuck cover or stopper, bent stiffeners, damaged glass, insecure refitting or abnormal movement during the wet-glass check: Stop for mismatched or stuck fittings, bent stiffeners, damaged glass or insecure refitting. Keep the wiper off if it is loose or moves abnormally and ask Mazda or a suitable repairer to inspect the attachment.

After the complete assembly is refitted, what did the safe parked wet-glass check show?

Matching rubber installed, original stiffeners reused, holder / cover / applicable stopper secured and satisfactory wet wiping observed: The rear-rubber replacement and actual wet-glass result are recorded. Continued noise, streaks or insecure retention still needs inspection.
A mismatched attachment, stuck cover or stopper, bent stiffeners, damaged glass, insecure refitting or abnormal movement during the wet-glass check: Stop for mismatched or stuck fittings, bent stiffeners, damaged glass or insecure refitting. Keep the wiper off if it is loose or moves abnormally and ask Mazda or a suitable repairer to inspect the attachment.
Work or the repeat observation is still incomplete: Preparation or incomplete work recorded. A satisfactory repeat observation is still pending.

Check and choose

Confirm your vehicle to start a check.

Your progress

No saved progress yet.

No result recorded.

Blank text checklist

Progress and observations stay on this browser. Take a dated copy to your next check or service visit.

1 Confirm your vehicle

2 Prepare

Keep the before and after.

3 Follow the steps

4 Check the result

Stop and get help if

Source & applicability

Is this a 2017 US Mazda3 5-Door with the original rear holder and cover shown on printed pages 6–33/34, matching replacement rubber, its stopper type identified and a way to support the arm without striking the glass?

After the complete assembly is refitted, what did the safe parked wet-glass check show?

All observation paths

Is this a 2017 US Mazda3 5-Door with the original rear holder and cover shown on printed pages 6–33/34, matching replacement rubber, its stopper type identified and a way to support the arm without striking the glass?

After the complete assembly is refitted, what did the safe parked wet-glass check show?

Related plans